hardware:routerstationpro
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
hardware:routerstationpro [2010/11/10 15:33] – created Michele Porelli | hardware:routerstationpro [2012/09/04 16:18] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== RouterStation Pro ====== | ====== RouterStation Pro ====== | ||
+ | ===== DebWRT ===== | ||
+ | ==== Build image ==== | ||
+ | * svn checkout https:// | ||
+ | * cd debwrt | ||
+ | * make menuconfig | ||
+ | * Target system is: Atheros AR71xx/ | ||
+ | * Subtarget is: Generic | ||
+ | * Target Profile is: Ubiquiti RouterStation Pro | ||
+ | * (if you are using usb drive instead of sd card) Enter in " | ||
+ | * (optional) make openwrt/ | ||
+ | * (optional) make openwrt/ | ||
+ | * make | ||
+ | ==== Prepare external rootfs (SD card or USB disk) ==== | ||
+ | * Partition the USB Disk/ | ||
+ | < | ||
+ | /dev/sdb2 - DEBWRT_SWAP - Linux Swap - 128MB</ | ||
+ | * Create filesystems | ||
+ | < | ||
+ | tune2fs -c 0 -i 0 /dev/sdb1 | ||
+ | mkswap / | ||
+ | ==== Copy rootfs on your SD card or USB disk ==== | ||
+ | * (if you have not automount) mkdir -p / | ||
+ | * make debian/ | ||
+ | ==== Flash firmware (kernel) ==== | ||
+ | * Follow [[hardware: | ||
+ | ==== Kernel upgrade ==== | ||
+ | Using "make openwrt/ | ||
+ | To use the newer kernel you must unpack bin/ | ||
+ | ===== OpenWRT ===== | ||
+ | ==== Build image ==== | ||
+ | * svn co [[svn:// | ||
+ | * cd trunk | ||
+ | * ./ | ||
+ | * ./ | ||
+ | * make menuconfig | ||
+ | * Target system is: Atheros AR71xx/ | ||
+ | * Subtarget is: Generic | ||
+ | * Target Profile is: Ubiquiti RouterStation Pro | ||
+ | * make | ||
+ | |||
+ | ==== Flash firmware ==== | ||
+ | * Connect your computer to the WAN port | ||
+ | * Configure your network like this: 192.168.1.1/ | ||
+ | * Plug in your RouterStation Pro | ||
+ | * Press the reset button and hold it for about 10 seconds (you should see the third led flash a bit and the second on come up) | ||
+ | * You should be able to ping 192.168.1.20 now | ||
+ | * Send the firmware image with tftp in binary mode: | ||
+ | < | ||
+ | tftp> binary | ||
+ | tftp> put openwrt-...-factory.bin</ | ||
+ | |||
+ | ==== Re-enable LAN ports ==== | ||
+ | * Install swconfig then: | ||
+ | < | ||
+ | swconfig dev eth1 set enable_vlan 1 | ||
+ | swconfig dev eth1 vlan 0 set ports '0 1 2 3 4' | ||
+ | swconfig dev eth1 set apply 1</ | ||
+ | |||
+ | ==== Install wireless cards ==== | ||
+ | * [[https:// | ||
+ | |||
+ | |||
===== Links ===== | ===== Links ===== | ||
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// | ||
+ | |||
===== Operating system ===== | ===== Operating system ===== | ||
- | * [[software: | + | * [[software: |
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// |
hardware/routerstationpro.1289399596.txt · Last modified: 2012/09/04 16:08 (external edit)