Differences

This shows you the differences between two versions of the page.

--- hardware:routerstationpro [2011/04/25 22:32] – Michele Porelli
+++ hardware:routerstationpro [2012/01/31 10:32] (current) – Michele Porelli
@@ Line 8: / Line 8: @@
   * Subtarget is: Generic
   * Target Profile is: Ubiquiti RouterStation Pro
+  * (if you are using usb drive instead of sd card) Enter in "Kernel Configuration" and edit the device in "Default kernel command line" from sda1 to sdb1
   * (optional) make openwrt/menuconfig
   * (optional) make openwrt/kernel_menuconfig
@@ Line 20: / Line 21: @@
 mkswap /dev/sdb2</code>
 ==== Copy rootfs on your SD card or USB disk ====
-  * (if you have not automount) mkdir -p /mnt/debwrt ; mount /dev/sdb1 /media/DEBWRT_ROOT
+  * (if you have not automount) mkdir -p /media/DEBWRT_ROOT ; mount /dev/sdb1 /media/DEBWRT_ROOT
-  * make debian/rootfs/install (Be careful! An rm -rf on /media/DEBWRT_ROOT is done first!)
+  * make debian/rootfs/install (Be careful! An rm -Rf on /media/DEBWRT_ROOT is done first!)
 ==== Flash firmware (kernel) ====
-Follow [[hardware:routerstationpro#Flash firmware|Router Station Pro OpenWRT flash instruction]] using bin/ar71xx-*-*-default/debwrt-firmware-ar71xx-generic-ubnt-rspro-squashfs-factory.bin
+  * Follow [[hardware:routerstationpro#Flash firmware|Router Station Pro OpenWRT flash instruction]] using bin/ar71xx-*-*-default/debwrt-firmware-ar71xx-generic-ubnt-rspro-squashfs-factory.bin
 ==== Kernel upgrade ====
-Using "make openwrt/kernel_menuconfig" you can tune your kernel configuration, after your customization you can compile running "make" (NOTE: if you don't have an older enviroment you must follow the instruction to [[hardware:routerstationpro#Build image|build a DebWRT image]])
+Using "make openwrt/kernel_menuconfig" you can tune your kernel configuration, after your customization you can compile running "make" (NOTE: if you don't have an older enviroment you must follow the instruction to [[hardware:routerstationpro#Build image|build a DebWRT image]])\\
 To use the newer kernel you must unpack bin/ar71xx-*-*-default/debwrt-modules-ar71xx-generic_UBNTRSPRO-*-*.tar.gz in /media/DEBWRT_ROOT/ (assuming that you have mounted DebWRT rootfs on /media/DEBWRT_ROOT/) and follow the instruction to [[hardware:routerstationpro#Flash firmware (kernel)|flash DebWRT kernel]]
 ===== OpenWRT =====
@@ Line 38: / Line 39: @@
   * Target Profile is: Ubiquiti RouterStation Pro
   * make
-==== Re-enable LAN ports ====
-  * Install swconfig then:
-<code>swconfig dev eth1 set reset 1
-swconfig dev eth1 set enable_vlan 1
-swconfig dev eth1 vlan 0 set ports '0 1 2 3 4'
-swconfig dev eth1 set apply 1</code>
 ==== Flash firmware ====
   * Connect your computer to the WAN port
@@ Line 54: / Line 50: @@
 tftp> binary
 tftp> put openwrt-...-factory.bin</code>
+==== Re-enable LAN ports ====
+  * Install swconfig then:
+<code>swconfig dev eth1 set reset 1
+swconfig dev eth1 set enable_vlan 1
+swconfig dev eth1 vlan 0 set ports '0 1 2 3 4'
+swconfig dev eth1 set apply 1</code>
+==== Install wireless cards ====
+  * [[https://forum.openwrt.org/viewtopic.php?id=24682|How-To]]