Differences

This shows you the differences between two versions of the page.

--- hardware:wbd-111 [2011/02/05 18:47] – created Michele Porelli
+++ hardware:wbd-111 [2012/10/08 21:21] (current) – [Build OpenWRT] Michele Porelli
@@ Line 1: / Line 1: @@
-====== Wilibox wbd-111 - Teltonika RUT-1xx ======
+====== Wilibox wbd-111 - (Teltonika RUT-1xx base board) ======
+===== OpenWRT =====
+==== Flash firmware ====
+Unfortunately sysupgrade is not yet implemented, you should go back to wikigear stock firmware then flash the new image
+==== Build OpenWRT ====
+      * download the latest trunk revision (you must use trunk because there are not a stable branch with gemini support):
+<code>svn co svn://svn.openwrt.org/openwrt/trunk/</code>
+  * add all available packages (download then "install"):
+<code>./scripts/feeds update -a
+./scripts/feeds install -a</code>
+  * <del>manually patch linux sources ([[https://dev.openwrt.org/attachment/ticket/6998/006-wbd111-enable-usb.patch]])
+Open arch/arm/mach-gemini/board-wbd111.c and add the green line in the right position
+Open drivers/usb/host/ehci-hcd.c and replace the zero with one in the correct line</del> - Fixed in r25820!
+  * prepare your image (remember to select everything you need):
+<code>make menuconfig</code>
+Select as Target system: Cortina CS351x (StormSemi SL351x)
+  * prepare your kernel (this step is uncommon, but it's indispensable for wbd-111):
+<code>make kernel_menuconfig</code>
+In this step you should include the right usb drivers:
+<code>
+**Device Drivers --->**
+**USB support --->**
+Mark as "built in" (*) **Support for Host-side USB**
+Mark as "built in" (*) **EHCI HCD (USB 2.0) support**
+esc-esc esc-esc... save!
+</code>
+To check if you have selected the correct driver after flashing image
+<code>dmesg | grep -i ehci-fotg2xx</code>
+should return
+<code>ehci-fotg2xx ehci-fotg2xx.0: Found Faraday OTG 2XX controller (base = 0x68000000)
+ehci-fotg2xx ehci-fotg2xx.0: FOTG2XX EHCI Host Controller
+ehci-fotg2xx ehci-fotg2xx.0: new USB bus registered, assigned bus number 1
+ehci-fotg2xx ehci-fotg2xx.0: irq 10, io mem 0x68000000
+ehci-fotg2xx ehci-fotg2xx.0: USB 0.0 started, EHCI 1.00, overcurrent ignored
+ehci-fotg2xx ehci-fotg2xx.0: role detected: Host,
+ehci-fotg2xx ehci-fotg2xx.0: A-Device
+ehci-fotg2xx ehci-fotg2xx.0: role detected: Host,
+ehci-fotg2xx ehci-fotg2xx.0: A-Device
+usb 1-1: new high speed USB device using ehci-fotg2xx and address 2</code>
+  * make the image (where 2 is the number of your processor's core):
+<code>make -j 2</code>
+==== Teltonika RUT-104 ====
+=== Enable hso (3g modem) support ===
+  * Select hso module in make menuconfig:
+<code>
+**Kernel modules  --->**
+**USB Support  --->**
+Mark as "built in" (*) **kmod-usb-net**
+Mark as "built in" (*) **kmod-usb-net-hso**
+Mark as "built in" (*) **kmod-usb-serial**
+Mark as "built in" (*) **kmod-usb-serial-option**
+esc-esc esc-esc... save!
+</code>
+  * Select PCCARD Bus support in make kernel_menuconfig:
+<code>
+**Bus support  --->**
+Mark as "built in" (*) **PCI support**
+Mark as "built in" (*) **PCCard (PCMCIA/CardBus) support  --->**
+**PCCard (PCMCIA/CardBus) support  --->**
+Mark as "built in" (*) **32-bit CardBus support**
+esc-esc esc-esc... save!
+</code>
+=== Add built-in hso comgt support ===
+  * Download and apply the patch to openwrt sources attached in [[https://dev.openwrt.org/ticket/6995|this ticket]].